Dashboard 3.8 and 4.2 Series 1 OTS and FHC (1961-67)
this black plasic cover is moulded perfectly to match clean at your existing dashboard
Requires: 1
demister nozzle - dashboard centre
OTS models
Requires: 1
dashboard, outer section, RH
Requires: 1
dashboard, outer section, LH
Requires: 1
Requires: 1
RH section with recess for speedometer and rev. counter. For RHD models
Requires: 1
LH section with recess for speedometer and rev. counter. For LHD models
Requires: 1
LH section with recess for glove box. For RHD models
Requires: 1
RH section with recess for glove box. For LHD models
Requires: 1
grab handle at side of dashboard - stainless steel reproduction
Requires: 2
under dashboard - 3-piece black millboard set for RHD models without air conditioning
Requires: 1
under dashboard - 3-piece black millboard set for LHD models without air conditioning
Requires: 1
in aluminium, with 'Polka Dot' pattern
3.8 Series 1 (1961-62) - OTS to 850609 and 878301
Requires: 1
3.8 Series 1 OTS from 850001 to 850943 (RHD) and from 875001 to 881887 (LHD), FHC from 860001 to 861799 (RHD) and from 885001 to 890873 (LHD) (1961-64)
Requires: 1
4.2 Series 1 OTS from 1E1001 to 1E1863 (RHD) and from 1E10001 to 1E15888 (LHD), FHC from 1E20001 to 1E21583 (RHD) and from 1E30001 to 1E34249 (LHD) (1964-67)
Requires: 1
and mesh for radio speaker
3.8 Series 1 OTS from 850001 to 850943 (RHD) and from 875001 to 881887 (LHD), FHC from 860001 to 861799 (RHD) and from 885001 to 890873 (LHD) (1961-64)
Requires: 2
radio speaker
4.2 Series 1 OTS from 1E1001 to 1E1863 (RHD) and from 1E10001 to 1E15888 (LHD), FHC from 1E20001 to 1E21583 (RHD) and from 1E30001 to 1E34249 (LHD) (1964-67)
Requires: 2
radio console, front
3.8 Series 1 OTS from 850001 to 850943 (RHD) and from 875001 to 881887 (LHD), FHC from 860001 to 861799 (RHD) and from 885001 to 890873 (LHD) (1961-64)
Requires: 1
radio console, front
4.2 Series 1 OTS from 1E1001 to 1E1863 (RHD) and from 1E10001 to 1E15888 (LHD), FHC from 1E20001 to 1E21583 (RHD) and from 1E30001 to 1E34249 (LHD) (1964-67)
Requires: 1
retaining blanging plate to radio console
Requires: 2
retaining blanging plate to radio console
Requires: 2
4.2 Series 1 OTS from 1E1001 to 1E1863 (RHD) and from 1E10001 to 1E15888 (LHD), FHC from 1E20001 to 1E21583 (RHD) and from 1E30001 to 1E34249 (LHD) (1964-67)
Requires: 1
ash tray blanking plate
4.2 Series 1 OTS from 1E1001 to 1E1863 (RHD) and from 1E10001 to 1E15888 (LHD), FHC from 1E20001 to 1E21583 (RHD) and from 1E30001 to 1E34249 (LHD) (1964-67)
Requires: 1
ash tray
4.2 Series 1 OTS from 1E1001 to 1E1863 (RHD) and from 1E10001 to 1E15888 (LHD), FHC from 1E20001 to 1E21583 (RHD) and from 1E30001 to 1E34249 (LHD) (1964-67)
Requires: 1
ash tray - complete with mounting kit
4.2 Series 1 OTS from 1E1001 to 1E1863 (RHD) and from 1E10001 to 1E15888 (LHD), FHC from 1E20001 to 1E21583 (RHD) and from 1E30001 to 1E34249 (LHD) (1964-67)
Requires: 1
with 'leaping cat' logo - chromed
3.8 Series 1 OTS from 850001 to 850943 (RHD) and from 875001 to 881887 (LHD), FHC from 860001 to 861799 (RHD) and from 885001 to 890873 (LHD) (1961-64)
Requires: 1
'Leaping Cat' on ashtray. Length approx. 30 mm, comes with stud and nut assembly
3.8 Series 1 OTS from 850001 to 850943 (RHD) and from 875001 to 881887 (LHD), FHC from 860001 to 861799 (RHD) and from 885001 to 890873 (LHD) (1961-64)
Requires: 1
chromed - required when radio is not fitted
Requires: 1
gearbox tunnel - fibreglass replacement
3.8 Series 1 plus 4.2 Series 1 OTS to 1E20102 (RH) and 1E10359 (LHD), FHC to 1E20102 (RHD) and 1E30349 (LHD) (1961-1964)
Requires: 1
gearbox tunnel - fibreglass replacement
Jaguar: E-Type 4.2 Series 1 OTS from 1E20103 (RH) and 1E10360 (LHD) plus FHC from 1E20103 (RHD) and 1E30350 (LHD) plus 2+2 with manual transmission from 1E50001 (RHD) and 1E75001 (LHD), all 4.2 Series 2 with manual transmission (1964-1970)
Requires: 1
rubber type
4.2 Series 1 without gear lever grommet (1964): FHC from chassis no. 1E20001 to 1E20102 (RHD) and from 1E30001 to 1E30349 (LHD), OTS from chassis no. 1E1001 to 1E1060 (RHD) and from 1E10001 to 1E10359 (LHD)
Requires: 1
rubber type
4.2 Series 1 with gear lever grommet (1964): FHC from chassis no. 1E20104 (RHD) and from 1E30351 (LHD), OTS from chassis no. 1E1062 (RHD) and from 1E10361 (LHD)
Requires: 1
gearbox tunnel
4.2 Series 1 OTS from 1E1001 to 1E1863 (RHD) and from 1E10001 to 1E15888 (LHD), FHC from 1E20001 to 1E21583 (RHD) and from 1E30001 to 1E34249 (LHD) (1964-67)
Requires: 1
mild steel
3.8 Series 1 OTS from 850001 to 850943 (RHD) and from 875001 to 881887 (LHD), FHC from 860001 to 861799 (RHD) and from 885001 to 890873 (LHD) (1961-64)
Requires: 1
mild steel
4.2 Series 1 OTS from 1E1001 to 1E1863 (RHD) and from 1E10001 to 1E15888 (LHD), FHC from 1E20001 to 1E21583 (RHD) and from 1E30001 to 1E34249 (LHD) (1964-67)
Requires: 1
remode control
3.8 Series 1 from OTS 850001 to 850609 (RHD) and 875001 to 878301 (LHD), FHC from 860001 to 860912 (RHD) and 885001 to 887131 (LHD) (1961-1962)
Requires: 1
remode control
3.8 Series 1 from OTS 850610 (RHD) and 878302 (LHD), FHC from 860913 (RHD) and 887132 (LHD) (1962-1964)
Requires: 1
remode control
4.2 Series 1 OTS from 1E1001 to 1E1863 (RHD) and from 1E10001 to 1E15888 (LHD), FHC from 1E20001 to 1E21583 (RHD) and from 1E30001 to 1E34249 (LHD) (1964-67)
Requires: 1
gear lever gaiter
3.8 and 4.2 Series with riveted shift lever cover OTS up to 1E1060 (RHD) and 1E10359 (LHD), FHC up to 1E20102 (RHD) and 1E30349 (LHD) (1961-64)
Requires: 1